Haeger 824 One-Touch

The 824 OT-5e is fully hydraulic, 8 ton of force, 24" throat depth, 4 station upper and lower tool changer, four auto feed bowls, full quality control

No alignment quick change tooling and is powered either by 220, or 480 three phase.

The OT-5e is best suited for high volume parts with flanges or boxes under 3" and fasteners up to 0616 ( M10 ) in mild steel and 0516 ( M6 ) in stainless.

The 824 OT-5e has a 4 station upper and lower auto tool changer and four auto feed bowls where you can insert 4 fasteners automatically allowing you to get the most benefit of single part handling.

Single Part Handling allows you to increase your process flow by inserting four different fasteners all with their own pressure settings and only handle the part once.

This machine also has full quality control with fastener length, fastener detection, insertion mapping, and program storage. 

Haeger's insertion Logic software has a built in wizard to quickly guide you through setting up a program based on the fasteners selected and automatically sets force, dwell, eject time, bowl vibration and all other settings needed.

The OT-5e does have some limitations for a normal Job Shop.

The machine cannot bottom feed nuts or use a J-frame attachment.

The OT-5e is used for high volume flat parts with flanges under 3".

Features

8 ton, 24 inch throat depth

The OneTouch comes standard with four nine-inch (MAS) Modular Autofeed Systems.

New Servo-Driven Tool Changer (Patented) offering a 3 Second Automatic Tool Change

Increased Part Clearance - up to 5.5"

New Shuttle Tooling Platform providing 2 Minute Tooling Set Up for any Fastener

New Upper Vacuum Tip System w/ Positive Locking

NEW LED Laser Part Locating Light

Latest Release of InsertionLogic Version 9 Software ­ includes InsertionGraphics, Networking Software, Offline Programming and Expanded Fastener Library

InsertionLogic Software + InsertionGraphics & Quality Control Pack

All NEW Version 9 w/ Optional Quality Control Pack includes Networking Software Communication, Off-line Programming and Digital Camera Package.

The Robot Ready Option configures the machine to connect to most robots.

4 MAS Units

4 Insertion Stations and 4 Tool positions provide the ability to automatically feed up to 4 different sizes and types of fasteners in one handling.

Productivity of 1 insertion every 2.5 seconds, while tools are changed within 3 seconds.

Fastener Detection and Fastener Length detection provides FULL process control in every station.

Operator Safety System

Haeger's patented Safety System is effective at any point in the ram stroke irrespective of the tooling length, requiring no set up by the operator; thus not affecting initial machine set up time.

Fully Hydraulic System

The OneTouch is extremely accurate and allows the operator to apply full tonnage at any point in the stroke.

Faster ram speed increases productivity reduces part cost and provides faster payback.

The electronically controlled hydraulic system assures the most repeatable force in the industry.

Low Energy Usage

The hydraulic system uses approximately 40% less energy than air or air over hydraulic methods making it less expensive to operate.

Positive Stop

Ideal for insertions into thin gauge materials and other delicate insertion applications where absolute repeatability is critical.

The Positive Stop is a standard feature and facilitates insertion in parts where pressures as low as 50lbs. may be needed.

Custom Tooling and Special Applications

Applications Haeger provides an unmatched selection of standard tooling in both inch and metric hardware, while Haeger's in-house capabilities provides solutions to engineer and manufacture manual and automatic tooling for virtually any fastener.

Laser Part Locating Light

The NEW Laser Part Locating Light guides your insertion process with a "red cross hair" laser locator to show exactly where each fastener is inserted.

The light provides fast hole location and identification.

Digital Camera Interface

The Haeger supplied digital camera, part of the Quality Control Pack, provides the ability to take part images at the machine and immediately import them into a part program.